Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Farm & ranch
Before
After
Before
After
Before
AfterGate Repair in Pico Rivera, CA
Gate access control in Pico Rivera usually means retrofitting an entry system onto a 1960s-era wrought iron gate whose original latch has long since failed. The dense concentration of post-WWII tract homes here, most built between the 1950s and 1970s, means our technicians regularly work on gates that predate modern keypads and card readers by decades. Call (562) 368-4485 and we’ll tell you exactly what your gate needs and what it costs, in writing, before any tool comes off the truck.
Why Pico Rivera Homes Are Different
Pico Rivera’s housing stock is overwhelmingly detached single-family homes built between 1945 and 1975, on modest lots with concrete driveways and block-wall perimeter fencing. Almost every one of those properties has a swing or slide driveway gate, and most of those gates are original wrought iron, now 40 to 60 years old. Along streets like Rosemead Boulevard and Washington Boulevard, we see hinge collars cracked from decades of daily cycling, bottom rails rotted through from ground contact, and post bases that flex because the concrete footer has crumbled.
The San Gabriel Valley floor adds two more failure drivers. Ground moisture near the San Gabriel River and Rio Hondo confluence accelerates rust on bottom rails and post bases, especially on streets bordering Rivera Park and the levee. Then come the fall Santa Ana winds, which routinely force gates off their hinges or bend lighter tubular frames on properties facing west or south. A gate that held for 50 years can fail in one October gust.
Our Main Pico Rivera Services
Most Pico Rivera homeowners reach us for one of three reasons: a gate that won’t open, a gate that needs replacing, or a motor that quit mid-cycle. Here’s what each involves locally.
Gate Repair in Pico Rivera
Repair work in Pico Rivera is dominated by hinge and weld failures on aging wrought iron, plus post-base corrosion from decades of soil contact. We cut out the rotted section, weld in fresh steel, align the gate, and leave you a photo record of every adjustment. Full details on Gate Repair in Pico Rivera.
Gate Installation in Pico Rivera
New gate installations here almost always involve removing a 50-year-old iron gate and setting new posts in a concrete driveway or block-wall footer. We measure the opening, quote the full job in writing, and schedule the removal and install around your property access. Full details on Gate Installation in Pico Rivera.
Gate Motor & Opener in Pico Rivera
Motor failures on Pico Rivera gates are frequently caused by Santa Ana wind loads pushing the gate past its travel limits, which burns out the limit switch or strips the drive gear. We diagnose the motor, check the physical gate alignment first, and replace only what failed. Full details on Gate Motor & Opener in Pico Rivera.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Pico Rivera
Gate access control in Pico Rivera means adding or repairing the electronics that let you open the gate without leaving the house, and the most common call we get is a keypad that worked for 20 years but now won’t respond. These systems, retrofitted onto gates built before access control existed, fail at the wiring connections and keypad membranes, both of which degrade faster in the moisture-heavy air along the river corridor. We service Gate Access Control systems including keypads, remotes, phone entry, card readers, and video intercoms.
Keypad Entry
Signs you need it
The keypad works intermittently, some buttons don’t respond, or the code stopped working entirely after rain.
What it costs in Pico Rivera
A keypad entry install or replacement typically runs $180 to $340, including sealed wiring connections.
How we do it
We test the existing wiring, replace the keypad, seal every connection against moisture, and photograph the finished work.
Remote Control
Signs you need it
You have to hold the remote at a specific angle or stand outside the car for the gate to respond.
What it costs in Pico Rivera
Remote control receiver and transmitter work typically runs $120 to $250 depending on the brand already installed.
How we do it
We check the receiver board, match the transmitter frequency, program the remote, and test range from the driver’s seat.
Phone Entry
Signs you need it
Visitors can’t call through to your phone, or the call goes through but the gate won’t open from the app.
What it costs in Pico Rivera
Phone entry system setup typically runs $250 to $450 with a standard call forwarding setup.
How we do it
We wire the phone entry module to the gate controller, program the forwarding number, and verify the open command.
What Gate Access Control Costs in Pico Rivera
| Item | Typical range in Pico Rivera |
|---|---|
| Keypad entry install or replacement | $180-$340 |
| Remote control receiver and transmitter | $120-$250 |
| Phone entry system setup | $250-$450 |
Can you add a keypad to my existing gate in Pico Rivera?
Yes. We add keypads and card readers to existing gates every week in Pico Rivera, including 1960s wrought iron. The wiring runs through the post or alongside the block wall. Call (562) 368-4485 for a written price.
Why did my gate opener stop responding after a Santa Ana wind event?
High wind forces the gate past its travel limit, which can trip the safety sensor or burn the limit switch. We reset the limits and photograph the new settings. Call (562) 368-4485 to book a diagnosis.
Gate Parts & Welding in Pico Rivera
Gate parts and welding in Pico Rivera usually starts with a bottom rail that has rusted through after 50 years of ground contact, or a hinge collar that cracked under wind load. On homes near the San Gabriel River levee, post bases corrode at double the rate we see a mile or two inland, so much of our welding work here is structural, not cosmetic. This is the core of our Gate Parts & Welding service.
Hinge Replacement
Signs you need it
The gate sags, drags on the driveway, or the hinge pin has visible play.
What it costs in Pico Rivera
Hinge replacement typically runs $120 to $300 per hinge, depending on the size and whether the post collar is intact.
How we do it
We cut off the failed hinge, weld on a new collar and pin, align the gate, and photograph the new weld.
Post Replacement
Signs you need it
The post wobbles when the gate moves, concrete around the base is cracked, or the gate no longer closes square.
What it costs in Pico Rivera
Post replacement typically runs $350 to $650 including new concrete and welding the hinge collars back on.
How we do it
We cut the old post at the footer, break out the remaining concrete, set a new post plumb, and re-hang the gate.
What Gate Parts & Welding Costs in Pico Rivera
| Item | Typical range in Pico Rivera |
|---|---|
| Hinge replacement | $120-$300 per hinge |
| Post replacement | $350-$650 |
| Bottom rail repair | $180-$350 |
Can you weld my wrought iron gate without removing it from the post?
Often yes, if the post is solid. We weld in place whenever possible, which saves the cost of re-hanging the gate. Call (562) 368-4485 for a written assessment.
Do you replace just the rusted bottom rail or the whole gate?
If the rest of the gate frame is sound, we cut out and weld in a new bottom rail for $180 to $350. If the frame is rotted in multiple places, replacement may cost less. We’ll show you photos before quoting.
Brands We Service in Pico Rivera
We service LiftMaster, FAAC, BFT, and Mighty Mule systems in Pico Rivera, among others. Common boards, remotes, and limit switches for these brands are stocked on our local trucks, so most motor and access-control repairs finish same-day. See our brands.
Pricing for Gate Repair in Pico Rivera, CA
| Service | Typical range in Pico Rivera |
|---|---|
| Hinge replacement | $120-$300 per hinge |
| Post replacement | $350-$650 |
| Bottom rail repair | $180-$350 |
| Keypad entry install or replacement | $180-$340 |
| Remote control receiver and transmitter | $120-$250 |
| Phone entry system setup | $250-$450 |
| Gate motor replacement | $500-$1,200 |
| Full gate installation | $1,500-$5,000 |
The two things that push price up in Pico Rivera are post footers that need re-pouring after 50 years of soil contact, and gates with wind damage that require straightening before they can be re-hung. Whatever the number, it’s written down and agreed before we begin. That’s Haven Standard Clause 1, on every job.
Neighborhoods We Serve in Pico Rivera
We work across all of Pico Rivera, from the older tract streets off Washington Boulevard to the homes bordering Rivera Park and the San Gabriel River levee. Typical response for non-emergency repair calls is same week, and emergency gate-outs are prioritized daily.
- Rivera Park area
- Washington Boulevard corridor
- Rosemead Boulevard corridor
- North Pico Rivera tract homes
- Pio Pico area
Service Area - Cities Near Pico Rivera
Vance Gate Repair serves Pico Rivera and surrounding communities with the same written-price policy and documented photo record on every job. We also cover Whittier, CA, Monterey Park, CA, Rosemead, CA, and El Monte, CA.
Serving Pico Rivera, CA - Our Local Coverage Area
We’re based in the Pico Rivera area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Pico Rivera
Live operators answer calls 24/7, and we schedule Pico Rivera non-emergency repairs within the same week. Emergency gate-outs, meaning a gate stuck open or blocking the driveway, are prioritized daily. Call (562) 368-4485 for today’s schedule.
For repair on an existing gate, no permit is typically required. For a full replacement with new posts and concrete footers, the city may require a simple building permit. We’ll tell you during the estimate if your project triggers one.
Yes. Under Haven Standard Clause 1, every Pico Rivera job gets a written flat price before any tool is picked up. You agree to the number first, and the final invoice matches that number unless you add scope.
If your gate is sagging, stuck, or refusing to open, call (562) 368-4485. A live person answers, the estimate is free, and the price is in writing before work begins.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Pico Rivera Customers Say
"Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N.